Verilink PRISM 3101 (34-00212) Product Manual Manuel d'utilisateur

iTRANSPORT®34-002123rd EditionPRISM 3101/3102T1/FT1 CSU/DSU

General 1-6PRISM 3101/3102

Installation 2-1PRISM 3101/31022. InstallationThis chapter contains instructions for physically installingthe TxPORT PRISM 3101/3102 as either a stan

Installation 2-2PRISM 3101/31023. To install the rack mount assembly into a rack, tightenthe four sets of nuts and bolts that attach the plate to the

Installation 2-3PRISM 3101/31022-B displays the pinout assignments for the 8-pin modularLAN connection. Configure the LAN interface before connecting

Installation 2-4PRISM 3101/3102linecoding of the network interface. ESF to D4 conversionis supported.NETThe Network interface connection contains an

Installation 2-5PRISM 3101/3102Power Connection AC powered units are powered by a 110 VAC captive powersupply. There is no power switch.DC powered un

Installation 2-6PRISM 3101/3102

Configuration 3-1PRISM 3101/31023. ConfigurationThe PRISM 3101/3102 can be configured through manualswitch settings and/or through a VT100 terminal c

Configuration 3-2PRISM 3101/3102ones density requirements of the T1 network line must beensured in this mode. Refer to the section entitledLine Param

Configuration 3-3PRISM 3101/3102Switch S4Switch S4 (Figure 3-5) configures the T1 DTE port. Anychannel not mapped to a data port is mapped to the T1

iiCopyright ©1996 TxPORT. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrievalsystem, o

Configuration 3-4PRISM 3101/3102Alarms Screen The Alarms screen (Figure 3-7) allows you to view the cur-rent alarm status of the network and the DTE

Configuration 3-5PRISM 3101/3102Reset Alarm Registers: Pressing <return> on (RESET)zeros the value of all Current alarm parameters, but does no

Configuration 3-6PRISM 3101/3102one or more of the signal status conditions listed inLine Fault and Loop Status on page 3-7. Completed Days: Displays

Configuration 3-7PRISM 3101/3102supports the following types of loops which are graphicallyrepresented on pages 3-8 and 3-9. Loop status changes can

Configuration 3-8PRISM 3101/3102Network Interface Framer/Deframer Multiplexor Receivers/DriversNETPLBBERT Generator/DetectorAll ones to DTEEIA 530 or

Configuration 3-9PRISM 3101/3102 Near Loops: Displays the loop status of the near element.Far Loops: Displays the loop status of the far element.Conf

Configuration 3-10PRISM 3101/3102Line ParametersThe Line Parameters screen (Figure 3-11) allows you toreview and set line parameters for the selected

Configuration 3-11PRISM 3101/3102T1-DTE Line Code: Sets the network side line coding aseither AMI or B8ZS.T1-DTE DSX Level: Specifies the DTE line

Configuration 3-12PRISM 3101/3102PORTCONFIGURATIONThe Port Configuration screen (Figure 3-13) sets the operat-ing parameters for each high speed port

Configuration 3-13PRISM 3101/3102RL (Remote Loop) Detect: Allows you to enable or dis-able the monitoring of pin BB (V.35) or pin 21 (EIA 530) toloo

iiiTable of Contents1. GeneralFeatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1Specifications . . . . . . . .

Configuration 3-14PRISM 3101/3102Reset String:These strings (1-5) are used to reconfigure theISDN TA when the unit has trouble making a connection.Co

Configuration 3-15PRISM 3101/3102SNMP CONFIGURATIONThe SNMP Configuration screen (Figure 3-16) is accessiblefor the SLIP, Ethernet or Token Ring SNMP

Configuration 3-16PRISM 3101/3102MANAGEMENTPORTSThe Management Ports screen (Figure 3-17) sets the fol-lowing parameters for the Call On Alarm (COA)

Configuration 3-17PRISM 3101/3102[DIRECT] - Sends reports directly to the SLIP server. Compressed SLIP: The choices are AUTO, ENABLE, andDISABLE. The

Configuration 3-18PRISM 3101/3102Set Date: The current date may be entered in this fieldusing the MM:DD:YY format. For example, July 4, 1993 isentere

Testing 4-1PRISM 3101/31024. TestingThis chapter describes hardware and software testing proce-dures and responses for the PRISM 3101/3102. Hardware

Testing 4-2PRISM 3101/3102

Treminal Interface A-1PRISM 3101/3102A.Terminal InterfaceThis chapter describes the screens structure and menu con-trols for the TxPORT PRISM 3101/31

Terminal Interface A-2PRISM 3101/3102For keyboards which do not have these standard keys orhave only some of them, an alternate set of cursor control

Pinout Tables B-1PRISM 3101/3102B.Pinout TablesThis appendix displays the pinout assignments for each portand option on the rear of the PRISM 3101/31

ivdsx1IntervalTable . . . . . . . . . . . . . . . . . . . . . . . . . C-3dsx1TotalTable . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4d

Pinout Tables B-2PRISM 3101/3102Data PortsSignal Name EIA 530 V.35 AcronymFrame Ground 1 A FGTransmit Data 2, 14 P, S TDReceive Data 3, 16 R, T RDReq

SNMP Agent C-1PRISM 3101/3102C.SNMP AgentThis unit has an embedded SNMP agent which can beaccessed either through the built in SLIP interface or theo

SNMP Agent C-2PRISM 3101/310219200 - returned for the SLIP Interface at 19200 baud38400 - returned for the SLIP Interface at 38400 baud56000 - return

SNMP Agent C-3PRISM 3101/3102SET: dsx1NoLoop(1) - deactivates any loops active on the unitdsx1PayloadLoop(2) - the unit will activate a PLB if noothe

SNMP Agent C-4PRISM 3101/3102dsx1IntervalSESs: (read-only)GET: returns the number of Severely Errored Seconds (per54016) in the specified 15 minute i

SNMP Agent C-5PRISM 3101/3102dsx1FarEndIntervalESs: (read-only)GET: returns the number of Errored Seconds (per 54016) in thespecified 15 minute inter

SNMP Agent C-6PRISM 3101/3102

PRISM 3101/3102 Page 1 of 1 TRANSPORT®45-00091-A1.01AddendumDocument:Date:34-00212-A3.01The power ratings, as listed on page 1-2 of the manual and in

General 1-1PRISM 3111/31121. GeneralThe TxPORT PRISM 3100 Series CSU/DSU terminates abroad range of T1/FT1 networking applications. The singleport 31

General 1-2PRISM 3101/3102• D4 or ESF line framing, AMI or B8ZS line coding • Supports Fractional T1 services with flexible bandwidth allo-cation •SL

General 1-3PRISM 3111/3112Internet: RFC1157 (SNMP)RFC1213 (MIB-II)RFC1406 (DS1 MIB)RFC1055 (SLIP)MIB-II: Device identification and interface per-for

General 1-4PRISM 3101/3102the warranty period, TxPORT will repair, or at TxPORT’soption, replace the unit free of charge.The remedies listed herein a

General 1-5PRISM 3111/3112When calling TxPORT for an RMA, please have the follow-ing information available.• Model number and serial number for each